Items where Author is "Hushim, Mohd Faisal "

Up a level
Export as [feed] RSS 2.0 [feed] RSS 1.0 [feed] Atom
Group by: Item Type | No Grouping
Number of items: 13.

Conference or Workshop Item

Hushim, Mohd Faisal and Alimin, Ahmad Jais and Razali, Mohd Azahari and Mohammed, Akmal Nizam and Sapit, Azwan and Mendez Carvajal, Julio Cesar (2015) Air flow behaviour on different intake manifold angles for small 4-stroke PFI retrofit kit system. In: International Engineering Research and Innovation Symposium 2015 (IRIS), 12–13 September 2015, Putrajaya, Malaysia.

Mohamad, Md. Nor Anuar and Manshoor, Bukhari and Hushim, Mohd Faisal and Amirnordin, Shahrin Hisham and Wan Muhammad, Wan Nur Azrina (2015) Development of twin piston expander with solenoid valve for organic rankine cycle. In: International Engineering Research and Innovation Symposium 2015 (IRIS), 12–13 September 2015, Putrajaya, Malaysia.

Razali, Mohd Azahari and Sapit, Azwan and Hushim, Mohd Faisal and Khalid, Amir and Masataro, Suzuki and Wataru, Masuda (2015) Flame spread behavior over combined fabric of cotton/polyester. In: International Engineering Research and Innovation Symposium 2015 (IRIS), 12–13 September 2015, Putrajaya, Malaysia.

Mohd Ali, Mas Fawzi and Mustaffa, Norrizal and Hushim, Mohd Faisal and Osman, Shahrul Azmir (2014) Application of injector-volume ratio values in the development of a fuel injection controller. In: International Integrated Engineering Summit (IIES 2014), 1-4 December 2014, Universiti Tun Hussein Onn Malaysia, Johor.

Sapit, Azwan and Razali, Mohd Azahari and Hushim, Mohd Faisal and Mohamad Jaat, Md Norrizam and Mohamad, Akmal Nizam and Khalid, Amir (2014) Dynamic behavior of rapeseed oil spray in diesel engine. In: International Integrated Engineering Summit (IIES 2014), 1-4 December 2014, Universiti Tun Hussein Onn Malaysia, Johor.

Hushim, Mohd Faisal and Alimin, Ahmad Jais and Mansor, Mohd Farris (2011) Effect of intake manifold angle of port-fuel injection retrofit-kit to the performances of an S.I. engine. In: Regional Conference on Automotive Research, 14th-15th December 2011, Kuala Lumpur.

Hushim, Mohd Faisal and Alimin, Ahmad Jais and Abdul Rashid, Lukman and Chamari, Mohd Firdaus (2011) Influence of fuel injector position of port-fuel injection retrofit-kit to the performances of small gasoline engine. In: 4th International Meeting on Advances in Thermofluids, 3rd-4th October 2011 , Melaka.

Hushim, Mohd Faisal and Alimin, Ahmad Jais and Mohammad, Md Nor Anuar and Madon, Rais Hanizam and Osman, Shahrul Azmir and Amirnordin, Shahrin Hisham and Salleh, Hamidon and Mohideen Batcha, Mohd Faizal (2011) Application of green technologies for UTHM in realizing the green campus concept. In: 2nd International Conference on Mechanical and Manufacturing Engineering (ICME 2011), 6th-7th June 2011, Putrajaya International Convention Centre, Putrajaya.

Hushim, Mohd Faisal and Osman, Shahrul Azmir and Alimin, Ahmad Jais and Mohamad, Akmal Nizam and Mustafa, Norrizal and Md Seri, Suzairin and Amirnordin, Shahrin Hisham and Wan Salim, Wan Saiful-Islam and Salleh, Hamidon and Azlan, Mohd Azwir (2011) Perodua Eco-Challenge 2010: ideas of modification from ARG UTHM. In: 2nd International Conference on Mechanical and Manufacturing Engineering (ICME 2011), 6th-7th June 2011, Putrajaya International Convention Centre, Putrajaya.

Hushim, Mohd Faisal and Alimin, Ahmad Jais and Mohideen Batcha, Mohd Faizal and Mohd Ali, Mas Fawzi and Abdul Rashid, Lukman (2011) Port-fuel injection system for small 4-stroke single cylinder engine: an experimental framework. In: 2nd International Conference on Mechanical and Manufacturing Engineering (ICME 2011), 6th-7th June 2011, Putrajaya International Convention Centre, Putrajaya.

Hushim, Mohd Faisal and Alimin, Ahmad Jais (2010) A review and investigation framework on port-fuel injection for small 4-stroke single cylinder engine. In: Postgraduate Seminar 2010, 29th and 30th November 2010, Universiti Tun Hussein Onn Malaysia.

Yusof, Yusri and Hushim, Mohd Faisal and Mamat, M. A. (2009) Comparison of product data model between rapid prototyping and CNC milling 3-Axis. In: Malaysian Technical Universities Conference on Engineering and Technology (MUCEET 2009), 20-22 June 2009, Kuantan, Pahang.

Rashid, L.A and Alimin, Ahmad Jais and Hushim, Mohd Faisal AN OVERVIEW ON DURABILITY STUDY ON A RETROFIT FUEL INJECTION KIT DURING ON-ROAD TESTING. In: Postgraduate Seminar 2010, 29 & 30 November 2010, UTHM.

This list was generated on Mon Nov 20 19:59:37 2017 MYT.