Items where Subject is "T Technology > TJ Mechanical engineering and machinery > TJ751-805 Miscellaneous motors and engines"

Up a level
Export as [feed] RSS 2.0 [feed] RSS 1.0 [feed] Atom
Group by: Creators | Item Type
Jump to: A | H | I | K | L | M | N | O | S | Y
Number of items at this level: 42.

A

Abdul Aziz, Mohamad Fuad (2015) The effect of ambient temperature to the performance of internal combustion engine. Masters thesis, Universiti Tun Hussein Onn Malaysia.

Abdul Kadir, Aeslina and Mohajerani, Abbas (2015) Effect of heating rate on gas emissions and properties of fired clay bricks and fired clay bricks incorporated with cigarette butts. Applied Clay Science, 104 . pp. 269-276. ISSN 0169-1317

Abdul Wahab, Abas (2008) Eqwin turbine – the break through for wind energy implementation in Malaysia. In: Proceedings of International Conference on Mechanical & Manufacturing Engineering (ICME2008), 21– 23 May 2008, Johor Bahru, Malaysia., 21-23 May 2008, Johor Bahru.

Abdullah, Mohammad Kamil and Aminnuddin, Hazim Fadli and Mohamad, Akmal Nizam (2014) Parametric study on anti-vortex film cooling hole arrangements. Applied Mechanics and Materials, 660 . pp. 664-668. ISSN 1662-7482

Alimin, Ahmad Jais and Benjamin, Stephen F. and Roberts, Carol A. (2007) Fuel penalty from periodic rich combustion of a diesel fuelled engine during lean NOx trap purging. In: 1st Engineering Conference (EnCon 2007), 28 December 2007, Universiti Malaysia Sarawak, Sarawak.

Andsaler, Adiba Rhaodah and Khalid, Amir and Him, Ramsy and Mohamad Jaat, Md Norrizam (2014) A review paper on simulation and modeling of combustion characteristics under high ambient and high injection of biodiesel combustion. In: International Integrated Engineering Summit (IIES 2014), 1-4 December 2014, Universiti Tun Hussein Onn Malaysia, Johor.

H

Hushim, Mohd Faisal and Alimin, Ahmad Jais (2010) A review and investigation framework on port-fuel injection for small 4-stroke single cylinder engine. In: Postgraduate Seminar 2010, 29th and 30th November 2010, Universiti Tun Hussein Onn Malaysia.

Hushim, Mohd Faisal and Alimin, Ahmad Jais and Abdul Rashid, Lukman and Chamari, Mohd Firdaus (2011) Influence of fuel injector position of port-fuel injection retrofit-kit to the performances of small gasoline engine. In: 4th International Meeting on Advances in Thermofluids, 3rd-4th October 2011 , Melaka.

Hushim, Mohd Faisal and Alimin, Ahmad Jais and Mansor, Mohd Farris (2011) Effect of intake manifold angle of port-fuel injection retrofit-kit to the performances of an S.I. engine. In: Regional Conference on Automotive Research, 14th-15th December 2011, Kuala Lumpur.

Hushim, Mohd Faisal and Alimin, Ahmad Jais and Mohammad, Md Nor Anuar and Madon, Rais Hanizam and Osman, Shahrul Azmir and Amirnordin, Shahrin Hisham and Salleh, Hamidon and Mohideen Batcha, Mohd Faizal (2011) Application of green technologies for UTHM in realizing the green campus concept. In: 2nd International Conference on Mechanical and Manufacturing Engineering (ICME 2011), 6th-7th June 2011, Putrajaya International Convention Centre, Putrajaya.

Hushim, Mohd Faisal and Alimin, Ahmad Jais and Mohideen Batcha, Mohd Faizal and Mohd Ali, Mas Fawzi and Abdul Rashid, Lukman (2011) Port-fuel injection system for small 4-stroke single cylinder engine: an experimental framework. In: 2nd International Conference on Mechanical and Manufacturing Engineering (ICME 2011), 6th-7th June 2011, Putrajaya International Convention Centre, Putrajaya.

Hushim, Mohd Faisal and Osman, Shahrul Azmir and Alimin, Ahmad Jais and Mohamad, Akmal Nizam and Mustafa, Norrizal and Md Seri, Suzairin and Amirnordin, Shahrin Hisham and Wan Salim, Wan Saiful-Islam and Salleh, Hamidon and Azlan, Mohd Azwir (2011) Perodua Eco-Challenge 2010: ideas of modification from ARG UTHM. In: 2nd International Conference on Mechanical and Manufacturing Engineering (ICME 2011), 6th-7th June 2011, Putrajaya International Convention Centre, Putrajaya.

I

Ismail, Muammar Mukhsin and Zulkifli, Abd Fathul Hakim and Mohd Ali, Mas Fawzi and Osman, Shahrul Azmir (2016) Conversion method of a diesel engine to a CNG-diesel dual fuel engine and its financial savings. ARPN Journal of Engineering and Applied Sciences, 11 (8). ISSN 18196608

K

Khalid, Amir and Manshoor, Bukhari (2013) Analysis of mixture formation and flame development of diesel combustion using a rapid compression machine and optical visualization technique. Applied Mechanics and Materials, 315 . pp. 293-298.

Khalid, Amir and Manshoor, Bukhari Effect of high injection pressure on mixture formation, burning process and combustion characteristics in diesel combustion. World Academy Of Science, Engineering and Technology 71 2012 .

Khalid , Amir and Alimin, Ahmad Jais and Mustaffa, Norrizal (2014) Development of constant volume chamber and high injection pressure system for bio-diesel combustion. Other thesis, Universiti Tun Hussein Onn Malaysia.

Khalid , Amir and Amirnordin, Shahrin Hisham and Lambosi, Latip and Manshoor, Bukhari and Sies, Mohamad Farid and Salleh, Hamidon (2014) Spray characteristic of diesel-water injector for burner system. Advanced Materials Research, 845 . ISSN 1662-8985

Khalid , Amir and Keisuke, Hayashi and Yoshiyuki , Kidoguchi and Tomoaki , Yatsufusa (2011) Effect of air entrainment and oxygen concentration on endothermic and heat recovery process of diesel ignition. 2011 JSAE/SAE International Powertrains, Fuels and Lubricants Meeting .

Khalid , Amir and Mohamad Jaat, Md Norrizam and Zaman, Izzuddin and Manshoor, Bukhari and Mohd Ali, Mas Fawzi (2013) Effect of pilot injection on mixture formation, ignition process and flame development in diesel combustion. Applied Mechanics and Materials , 390 . pp. 327-332.

Khalid , Amir and Mohamad Jaat, Md Norrizam and Zaman, Izzuddin and Manshoor, Bukhari and Mohd Ali, Mas Fawzi (2013) Effect of preheated fuel on mixture formation of biodiesel spray. Applied Mechanics and Materials , 393 . pp. 493-498.

Khalid , Amir and Tomoaki , Yatsufusa and Takayuki , Miyamoto and Jun , Kawakami and Yoshiyuki , Kidoguchi (2009) Analysis of relation between mixture formation during ignition delay period and burning process in diesel combustion. In: 15th Small Engine Technology Conference (SETC 2009), 3rd-5th November 2009, Penang, Malaysia.

Khalid , Amir and Yoshiyuki, Kidoguchi (2010) Analysis of diesel combustion using a rapid compression machine and optical visualization technique. In: 2nd International On-Board Symposium : Human Health, Energy and Environment, Japan.

L

Liong, Boon Yoong and Zakaria , Mohamad Fauzi and Hashim, Hairulazwan (2012) Design and development of spinning LED message display system. In: Proceeding of National Conference of Electric and Electronic Engineering 2012, 2012.

M

Md Yazid, Muhammad Haziq and Salleh, Hamidon and Azahari, Razali (2014) An experiment investigation of film cooling effectivenes of sister hole of cylindrical shaped hole film cooling geometry on a flat plate surface. In: International Integrated Engineering Summit (IIES 2014), 1-4 December 2014, Universiti Tun Hussein Onn Malaysia, Johor.

Mohamad, Md Nor Anuar (2010) Efficiency analysis of automotive hydrogen internal combustion engine combined with a steam rankine cycle. Masters thesis, Nagaoka University of Technology.

Mohamed Zarti , Almehdi (2012) Gas turbine performance based creep life estimation using soft computing technique. Masters thesis, Universiti Tun Hussein Onn Malaysia.

Mohammed, Mohammed Akram (2014) Quasiturbine rotor development optimization. Masters thesis, Universiti Tun Hussein Onn Malaysia.

Mohd Ali, Mas Fawzi and Mustaffa, Norrizal and Hushim, Mohd Faisal and Osman, Shahrul Azmir (2014) Application of injector-volume ratio values in the development of a fuel injection controller. In: International Integrated Engineering Summit (IIES 2014), 1-4 December 2014, Universiti Tun Hussein Onn Malaysia, Johor.

Mohd Ali, Mas Fawzi (2007) Development of a direct fuel injector for a two-stroke gasoline engine. Masters thesis, Universiti Teknologi Malaysia.

Mustaffa, Norrizal (2013) Effects of biodiesel fuel temperature on performance and emissions of a compression ignition (CI) engine. Masters thesis, Universiti Tun Hussein Onn Malaysia.

Mustaffa, Norrizal and Khalid , Amir and Sies, Mohamad Farid and Zakaria, Hanis and Manshoor, Bukhari (2014) Performance and emissions of preheated biodiesel on a compression ignition (CI) engines. Applied Mechanics and Materials , 465 . pp. 291-295. ISSN 1660-9336

Mustaffa, Norrizal and Khalid , Amir and Sies, Mohamad Farid and Zakaria, Hanis and Manshoor, Bukhari (2014) Preheated biodiesel derived from vegetable oil on performance and emissions of diesel engines: a review. Applied Mechanics and Materials , 465 . pp. 285-290. ISSN 1660-9336

N

Noor Balia, Fuadi and Ridha, Muhammad and Mahzan @ Mohd Zin, Shahruddin and AB Wahab, Abas (2011) Investigation into piston-slap force under friction and connecting rod effects of diesel engine. In: International Conference on Advanced Science, Engineering and Information Technology 2011, 14-15, January 2011, Hotel Equatorial Bangi-Putrajaya.

O

Omar Kamal, Shahrul Nahar (2015) Analysis of performance and emission of different gasoline fuel on small duty engine at various ambient temperatures. Masters thesis, Universiti Tun Hussein Onn Malaysia.

Osman, Shahrul Azmir (2014) Characterization of a C.I. engine operated using retrofit monogas fuelling concept. PhD thesis, Universiti Tun Hussein Onn Malaysia.

Osman, Shahrul Azmir and Alimin, Ahmad Jais and Ismail, Mohd Yusri and Koh, Wern Hui (2013) Performance and emission characteristics of direct injection C.I engine retrofitted with mono-CNG system. In: Asia Conference on Mechanical and Materials Engineering (ACMME 2013) , 8-9 October 2013, Wuhan, China .

S

Salleh, Hamidon and R. Ragavan, Vijay and Kenichi, Funazaki and Alimin, Ahmad Jais and Md Seri, Suzairin and Mohideen Batcha, Mohd Faizal and Atan, Siti Rohila (2013) Hydrodynamic and thermal characteristics study of cooling structure (IIC) for eco-gas turbine engine blade. Other thesis, Universiti Tun Hussein Onn Malaysia.

Samsudin, Dahrum and Othman, Safwan and Anuar, M. D. and Manshoor, Bukhari and Khalid, Amir (2014) Experimental investigation of mixture formation and flame development using the basics technique of schlieren optical visualization principle. Applied Mechanics and Materials, 660 . pp. 474-478. ISSN 1662-7482

Sapit, Azwan and Razali, Mohd Azahari and Mohamad Jaat, Md Norrizam and Mohamad, Akmal Nizam and Khalid, Amir and Manshoor, Bukhari (2014) Optical technique using nano-spark lightsource for macro and microscale image acquisition to study diesel spray atomization. In: International Integrated Engineering Summit (IIES 2014), 1-4 December 2014, Universiti Tun Hussein Onn Malaysia, Johor.

Sies, Mohamad Farid and Mustaffa, Norrizal and Zakaria, Hanis and Salleh, Hamidon and Manshoor, Bukhari and Khalid , Amir (2014) A review of the concept of fuel-water internally rapid mixing injector in burner system. Applied Mechanics and Materials , 465 . pp. 296-301. ISSN 1660-9336

Suardi, Mirnah and Azman, Norazwan and Samsudin, Dahrum and Amirnordin, Shahrin Hisham and Khalid , Amir (2014) Effect of mixture formation of biodiesel-water-air rapid mixing derived from crude palm oil and waste cooking oil in burner combustion. Applied Mechanics and Materials, 660 . pp. 421-425. ISSN 1662-7482

Y

Yii, Ronny Shi Chin (2016) Simulation of different orifice geometries on premix injector. Masters thesis, Universiti Tun Hussein Onn Malaysia.

This list was generated on Sat May 27 11:46:10 2017 MYT.